Perfect Tender Flaky Pie Crust Recipes

Steps:

• Whisk the flour and salt together in a medium size bowl. With a pastry blender, cut in the cold shortening until the mixture resembles coarse crumbs. Drizzle 2 to 3 tablespoons ice water over flour. Toss mixture with a fork to moisten, adding more water a few drops at a time until the dough comes together.
• Gently gather dough particles together into a ball. Wrap in plastic wrap, and chill for at least 30 minutes before rolling.
• Roll out dough, and put in a pie plate. Fill with desired filling and bake.

Steps:

• Measure flour and salt into bowl. Add oil; mix with a fork, until particals are the size of small peas. Sprinkle with water, 1 tablespoon at a time, until flour is moistened and dough almost cleans the sides of the bowl. (If dough seems too dry, 1 to 2 tablespoons oil can be added. Do not add water.If dough seems a bit too wet, add a tiny bit of additional flour).Gather dough together;PRESS FIRMLY INTO A BALL. After pressing firmly into a ball,the less the dough is handled the more flaky the crust will be.
• Divide dough in half ; place one half cut side down and flatten into a round. Roll each round of dough between two sheets of wax paper. Gently peel off one sheet of wax paper and turn dough upside down. Peel off remaining sheet of wax paper after placing bottom crust into pan leaving a 1/2 inch overlap around pan edge.( Fill with desired pie filling.) Repeat with top crust rolling out same as bottom crust leaving 1 inch overhang around pan edge). Fold and roll top edge under lower edge, pressing on the rim to seal; flute edges as desired.
• Cut slits to vent steam in top of pie. I usually moisten my hands with a little water and dab across top crust. Sprinkle a tiny bit of sugar across the top of the pie, but not on the fluted areas of crust. Bake as directed following your pie recipe.
• *Do not use quick mixing flour in this recipe. If using self-rising flour,omit the salt. Pie crusts made with self-rising flour will differ in flavor and texture from those made with regular flour. (I always use regular flour.).
• Lots of people say they can't make a good pie crust. You can using this recipe,just work with the dough. It may take a time or two, until you become used to making the dough and working with it. Just remember to press the dough into a firm ball before rolling it out between the wax paper sheets. Another small bonus for me is that it uses oil instead of hydrogenated fats.

Steps:

• In a large bowl, mix together flour, salt, and sugar until well combined. Using clean hands, add butter and toss until just coated. Rub butter between thumb and forefingers to incorporate into flour mixture until butter is in lima bean-sized pieces and comes together in quarter-sized clumps when squeezed in palm, about 2 minutes. Add shortening, toss until just coated in flour, then rub into flour mixture until mixture forms pea-size pieces (some big chunks should remain) and comes together in fist-sized clumps when squeezed, about 1 minute. Drizzle in half ice water and rake through mixture with fingers until just moistened. Drizzle in remaining water 1 tablespoon at a time and comb through mixture with fingers to moisten. It will go from being a shaggy mess to coming together. Dough is moist enough when it is moistened through but is not wet when pressed. (Do not overwork the dough or it will become tough.)
• While rotating the bowl with 1 hand, push dough between other palm and side of bowl to gather into a ball. Turn dough onto a piece of plastic wrap, press it into a flat disk, then close in wrap. Place in coldest part of refrigerator (usually back bottom shelf) at least 30 minutes before rolling out and forming into a crust.

Steps:

• For a flaky, tender crust (as opposed to one that's harder, mealy, and more cookie-like), the following works well.
• Whisk together all of the dry ingredients, reserving a few tablespoons of the flour.
• Cut in half of the fat, working the mixture until it's mealy and crumbly.
• Place the reserved flour on your work surface, and coat the remaining fat with the flour.
• Use a rolling pin or the heel of your hand to flatten the fat till it's about 1/2-inch thick.
• Break this flour-coated fat into 1-inch pieces, and mix it into the dough, just till it's evenly distributed; some of the pieces of flour-coated fat should break into smaller pieces.
• Sprinkle the liquid(s) over the dough while tossing with a fork.
• Just as soon as the dough becomes cohesive (i.e., you can squeeze it into a ball easily), stop mixing; there should still be visible pieces of fat in the dough.
• Flatten the dough into a disk and wrap it in plastic wrap or waxed paper.
• Refrigerate for 30 minutes or longer; this resting period allows the flour to absorb the water, making the dough easier to roll out.
• Flour your work surface and roll the dough into a 12 x 9-inch (approximately) rectangle.
• (If it isn't holding together well, sprinkle it lightly with a couple of teaspoons of water.
• Fold the dough into thirds (like a letter), then fold it into thirds the opposite way, to form a rough square. Wrap it well and refrigerate again.).
• When you're "ready to roll," remove the dough from the fridge.
• If the dough is made with all lard and/or vegetable shortening, you'll be able to work with it directly from the refrigerator.
• A dough made with all butter will need to warm slightly (10 to 15 minutes) before rolling, as butter becomes brittle when it's refrigerated.
• Dough made with a combination of butter and shortening should rest for about 5 minutes at room temperature before rolling.
• Roll the dough to the size needed (about 13 inches for a 9-inch pie).
• Fill and bake as directed in your recipe.
• Note: in this particular recipe, cut all of the lard or vegetable shortening into the flour, then coat the butter with flour before adding it to the dough.

Steps:

• Whisk flour with salt in a bowl; use a fork to stir in vegetable oil. Mix in water, 1 tablespoon at a time, before adding more water. Gather dough into a ball, divide in half, and roll out on a floured work surface.