Whiskey Glazed Ham Recipes

Steps:

• Whisk together the honey, marmalade, mustard and whiskey in a medium bowl until completely combined. Using the Instant Pot® metal insert as a guide, trim the ham to fit; reserve the trimmings for another use. Place two 24-inch pieces of twine criss-crossing one another on a clean work surface and place a 24-inch piece of heavy-duty foil over the top of the twine. Place the ham cut-side down in the center of the foil. Fold the corners up over the shank end (the narrow end of the ham bone) so that most of the ham is covered with foil. Take the 2 ends of one piece of twine and tie them into a tight knot around the ham. Repeat with the remaining twine so that you have 2 twine handles to support and lift the ham.
• Set a rack inside the pot and add 2 cups water. Using the twine handles, place the ham inside the pot. Fold open the foil corners so that the ham is exposed and pour the honey mixture over the ham. Fold closed the foil corners so that the ham is covered. Follow the manufacturer's guide for locking the lid and preparing to cook. Set to pressure cook on high pressure for 10 minutes (see Cook's Note).
• After the pressure-cook cycle is complete, follow the manufacturer's guide for quick release and wait until the quick-release cycle is complete. Be careful of any remaining steam, unlock and remove the lid.
• Lift the ham out of the pot, place in a large bowl and carefully drain the glaze and cooking juices; transfer the ham to a rimmed baking sheet, cover with foil and let sit until ready to glaze.
• Remove the rack from the pot and discard the water. Place the pot back in the base, set to saute on high and add the glaze. Cook until reduced, thick and syrupy, about 25 minutes. Brush the glaze over the ham and inside each slice; serve.

Steps:

• Preheat the oven to 325 degrees F. Let the ham sit at room temperature for 30 minutes and trim off any skin. If your ham is not a spiral-cut ham, use a sharp paring knife to score through the fat in a diagonal crosshatch pattern without cutting through to the meat.
• Place the ham, flat side down, on a roasting rack in a roasting pan. Pour 1 cup water into the pan. Bake until a thermometer inserted into the thickest part of the ham registers 130 degrees F, about 2 hours 30 minutes (about 15 minutes per pound-reduce the time to 10 minutes per pound for a spiral-cut ham).
• Meanwhile, make the glaze: Whisk the brown sugar, maple syrup, soy sauce, orange zest and juice, Dijon, vinegar, cinnamon, cloves, onion powder and a few grinds of black pepper in a medium saucepan until smooth. Bring to a boil over medium-high heat, whisking occasionally, then reduce the heat to low and simmer until the glaze has thickened and reduced by half (you should have 1 cup glaze), 20 to 25 minutes. Set aside until the ham is ready.
• Increase the oven temperature to 425 degrees F. Brush half of the glaze over the ham. If the water in the bottom of the pan has evaporated, add 1 cup water. Return the ham to the oven and roast for 30 minutes, brushing with the remaining glaze every 10 minutes (two more times) before returning to the oven.
• Let the ham cool for 15 minutes before thinly slicing.

Steps:

• Preheat oven to 325 degrees F (165 degrees C).
• Remove skin and excess fat from ham, leaving a fat layer about 1/4-inch thick. Score ham in a diamond pattern with a sharp knife. Push cloves into the center of the scored diamond shapes. Place ham with cut side down into a roasting pan.
• Bake ham in the preheated oven until an instant-read meat thermometer inserted into the thickest part of the meat, not touching bone, reads 125 degrees F (52 degrees C), about 2 hours.
• Combine brown sugar, whiskey, and black pepper in a bowl until glaze is smooth.
• Raise oven temperature to 375 degrees F (190 degrees C).
• Baste ham with 1/3 the whiskey glaze. Return to oven and bake until internal temperature reaches 140 degrees F (60 degrees C), basting ham with whiskey glaze every 10 minutes. Cover ham loosely with a tent of aluminum foil if ham browns too quickly.
• Let ham rest for 15 minutes before carving.